In computer networking, a wireless access point (WAP), or more generally just access point (AP), is a networking hardware device that allows a Wi-Fi device to connect to a wired network. The AP usually connects to a router (via a wired network) as a standalone device, but it can also be an integral component of the router itself. An AP is differentiated from a hotspot, which is the physical location where Wi-Fi access to a WLAN is available.
Video Wireless access point
Introduction
Prior to wireless networks, setting up a computer network in a business, home or school often required running many cables through walls and ceilings in order to deliver network access to all of the network-enabled devices in the building. With the creation of the wireless access point, network users were able to add devices that access the network with few or no cables. An AP normally connects directly to a wired Ethernet connection and the AP then provides wireless connections using radio frequency links for other devices to utilize that wired connection. Most APs support the connection of multiple wireless devices to one wired connection. Modern APs are built to support a standard for sending and receiving data using these radio frequencies. Those standards, and the frequencies they use are defined by the IEEE.
Maps Wireless access point
Wireless access point vs. ad hoc network
Some people confuse wireless access points with wireless ad hoc networks. An ad hoc network uses a connection between two or more devices without using a wireless access point: the devices communicate directly when in range. An ad hoc network is used in situations such as a quick data exchange or a multiplayer LAN game because setup is easy and does not require an access point. Due to its peer-to-peer layout, ad hoc connections are similar to Bluetooth ones.
But ad hoc connections are generally not recommended for a permanent installation. The reason is that Internet access via ad hoc networks, using features like Windows' Internet Connection Sharing, may work well with a small number of devices that are close to each other, but ad hoc networks don't scale well. Internet traffic will converge to the nodes with direct internet connection, potentially congesting these nodes. For internet-enabled nodes, access points have a clear advantage, with the possibility of having a wired LAN.
Limitations
It is generally recommended that one IEEE 802.11 AP should have, at a maximum, 15-25 clients per radio (most APs having between 1 and 4 radios). However, the actual maximum number of clients that can be supported can vary significantly depending on several factors, such as type of APs in use, density of client environment, desired client throughput, etc. The range of communication can also vary significantly, depending on such variables as indoor or outdoor placement, height above ground, nearby obstructions, other electronic devices that might actively interfere with the signal by broadcasting on the same frequency, type of antenna, the current weather, operating radio frequency, and the power output of devices. Network designers can extend the range of APs through the use of repeaters, which amplify a radio signal, and reflectors, which only bounce it. In experimental conditions, wireless networking has operated over distances of several hundred kilometers.
Most jurisdictions have only a limited number of frequencies legally available for use by wireless networks. Usually, adjacent APs will use different frequencies (Channels) to communicate with their clients in order to avoid interference between the two nearby systems. Wireless devices can "listen" for data traffic on other frequencies, and can rapidly switch from one frequency to another to achieve better reception. However, the limited number of frequencies becomes problematic in crowded downtown areas with tall buildings using multiple APs. In such an environment, signal overlap becomes an issue causing interference, which results in signal droppage and data errors.
Wireless networking lags wired networking in terms of increasing bandwidth and throughput. While (as of 2013) high-density 256-QAM (TurboQAM) modulation, 3-antenna wireless devices for the consumer market can reach sustained real-world speeds of some 240 Mbit/s at 13 m behind two standing walls (NLOS) depending on their nature or 360 Mbit/s at 10 m line of sight or 380 Mbit/s at 2 m line of sight (IEEE 802.11ac) or 20 to 25 Mbit/s at 2 m line of sight (IEEE 802.11g), wired hardware of similar cost reaches closer to 1000 Mbit/s up to specified distance of 100 m with twisted-pair cabling in optimal conditions (Category 5 (known as Cat-5) or better cabling with Gigabit Ethernet). One impediment to increasing the speed of wireless communications comes from Wi-Fi's use of a shared communications medium: Thus, two stations in infrastructure mode that are communicating with each other even over the same AP must have each and every frame transmitted twice: from the sender to the AP, then from the AP to the receiver. This approximately halves the effective bandwidth, so an AP is only able to use somewhat less than half the actual over-the-air rate for data throughput. Thus a typical 54 Mbit/s wireless connection actually carries TCP/IP data at 20 to 25 Mbit/s. Users of legacy wired networks expect faster speeds, and people using wireless connections keenly want to see the wireless networks catch up.
By 2012, 802.11n based access points and client devices have already taken a fair share of the marketplace and with the finalization of the 802.11n standard in 2009 inherent problems integrating products from different vendors are less prevalent.
Security
Wireless access has special security considerations. Many wired networks base the security on physical access control, trusting all the users on the local network, but if wireless access points are connected to the network, anybody within range of the AP (which typically extends farther than the intended area) can attach to the network.
The most common solution is wireless traffic encryption. Modern access points come with built-in encryption. The first generation encryption scheme, WEP, proved easy to crack; the second and third generation schemes, WPA and WPA2, are considered secure if a strong enough password or passphrase is used.
Some APs support hotspot style authentication using RADIUS and other authentication servers.
Opinions about wireless network security vary widely. For example, in a 2008 article for Wired magazine, Bruce Schneier asserted the net benefits of open Wi-Fi without passwords outweigh the risks, a position supported in 2014 by Peter Eckersley of the Electronic Frontier Foundation.
The opposite position was taken by Nick Mediati in an article for PC World, in which he takes the position that every wireless access point should be protected with a password.
See also
- Femtocell - a local-area base station using cellular network standards such as UMTS, rather than Wi-Fi
- HomePlug
- List of wireless router firmware projects
- LWAPP - Lightweight Access Point Protocol used to manage a large set of APs
- Wi-Fi Array System of multiple APs
- Wi-Fi Direct - a Wi-Fi standard that enables devices to connect with each other without requiring a (hardware) wireless access point and to communicate at typical Wi-Fi speeds
- WiMAX - wide-area wireless standard that has a few elements in common with Wi-Fi
- Wireless LAN - networks consisting of one or more access points plus one or more devices
References
Source of article : Wikipedia
0 Comments